Appendix B
ISL Messages
ISL: KERNEL (knlname) LOAD COMPLETED
| Cause: | A kernel has been loaded successfully.
|
| Action: | None. |
ISL(rev#): RESTARTED. REASON = xxxx...
| Cause: | Re-ISL and Re-INIT processing starts.
| rev#: | ISL revision |
| xxxx: | Cause of re-ISL |
| SHUTDOWN COMMAND (-I5): | -I5 option for shutdown |
| SHUTDOWN COMMAND (-I6): | -I6 option for shutdown |
| FSCK CHECK: | File system check |
| KERNEL PANIC: | Kernel panic |
| KERNEL STALL: | Kernel stall |
|
| Action: | None. |
ISL: aocspof(3): The system power will be off.
| Cause: | The system power-off is issued. The power will be turned off soon. |
| Action: | None. |
ISL: UPDATING ISL COMPLETED.
| Cause: | Updating the ISL file completed. |
| Action: | None. |
ISL: IOP initializing. IOPNO=0xXXXX. Please wait max tt sec.
| Cause: | IOP initialization starts. Wait for a maximum of tt seconds.
| XXXX: | Bit position from the left of the IOP to be initialized
Example:
| Only IO0 | 0x8000 |
| IO0 and IO1 | 0xc000 |
|
| tt: | Maximum time period for initialization |
|
| Action: | None. |
ISL: END REBOOT.
| Cause: | Automatic restarting of DGP completed during ISL operation. |
| Action: | None. |
ISL: isl(islname) updating.
| Cause: | Updating the ISL file starts. Wait for about five minutes.
|
| Action: | None. |
ISL: (rev#) is ready. KERNEL= knlname KDB= [ON|OFF]
| Cause: | ISL is activated.
| rev#: | ISL revision number |
| knlname: | Kernel name to be loaded |
| KDB=: | Specify whether to activate the kernel to be loaded with KDB=ON. |
|
| Action: | None. |
ISL: (rev#) is ready. (F3MODE) KERNEL= knlname KDB= [ON|OFF]
| Cause: | ISL is activated in the dump collection mode.
| rev#: | ISL revision number |
| knlname: | Kernel name to be loaded |
| KDB=: | Specify whether to activate the kernel to be loaded with KDB=ON. |
|
| Action: | None. |
ISL: (rev#) is ready. (F3MODE:TIMEOUT) KERNEL= knlname KDB= [ON|OFF]
| Cause: | ISL is automatically activated in the dump collection mode
due to the WDT time out.
| rev#: | ISL revision number |
| knlname: | Kernel name to be loaded |
| KDB=: | Specify whether to activate the kernel to be loaded with KDB=ON. |
|
| Action: | None. |
ISL: (rev#) is ready. (HWREBOOT) KERNEL= knlname KDB= [ON|OFF]
| Cause: | ISL is automatically activated
after the hardware failure recovery processing completed.
| rev#: | ISL revision number |
| knlname: | Kernel name to be loaded |
| KDB=: | Specify whether to activate the kernel to be loaded with KDB=ON. |
|
| Action: | None. |
ISL: exchanged the path to SIOX for 2nd path to SIOX.
| Cause: | The path for SIOX is switched. |
| Action: | None. |
ISL: lookup: knlname NOT FOUND
| Cause: | The specified kernel is not found.
|
| Action: | Specify a correct kernel name. |
ISL: IO INITIALIZE FAILURE. IO# CC = cc#
| Cause: | The initialization of IO io# failed.
| io#: | IO number |
| cc#: | Condition code |
For an IO of system control IOX, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel, the message is output to
the console. |
| Action: | Contact your NEC service representative. |
ISL: IOio# INITIALIZE FAILURE. STATUS = status
| Cause: | The initialization of IO io# failed.
| io#: | IO number |
| status: | Operation result |
For an IO of system control IOX, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel, the message is output to
the console. |
| Action: | Contact your NEC service representative.
|
ISL: IOio# CONNECT FAILURE. CC = cc#
| Cause: | The connection of IO io# failed.
| io#: | IO number |
| cc#: | Condition code |
For an IO of system control IOX, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel,
the message is output to the console. |
| Action: | Contact your NEC service representative. |
ISL: IOio# CHECK
| Cause: | A fault occurred in IO io#.
For an IO of system control IOX, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel, the message is output to
the console. |
| Action: | Contact your NEC service representative.
|
ISL: IOio# CHch# INITIALIZE FAILURE. CC = cc#
| Cause: | The initialization of channel ch# of IO io# failed.
| io#: | IO number |
| ch#: | Channel number |
| cc#: | Condition code |
For a system control IOX channel, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel,
the message is output to the console. |
| Action: | Contact your NEC service representative.
|
ISL: IOio# CHch# INITIALIZE FAILURE. STATUS = status
| Cause: | The initialization of channel ch# of IO io# failed.
| io#: | IO number |
| ch#: | Channel number |
| status: | Operation result |
For a system control IOX channel, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel,
the message is output to the console. |
| Action: | Contact your NEC service representative.
|
ISL: IOio# CHch# CONNECT FAILURE. CC = cc#
| Cause: | The connection of channel ch# of IO io# failed.
| io#: | IO number |
| ch#: | Channel number |
| status: | Operation result |
For a system control IOX channel, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel,
the message is output to the console. |
| Action: | Contact your NEC service representative.
|
ISL: IOio# CHch# DISCONNECT FAILURE. CC = cc#
| Cause: | The disconnection of channel ch# of IO io# failed.
| io#: | IO number |
| ch#: | Channel number |
| status: | Operation result |
For a system control IOX channel, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel,
the message is output to the console. |
| Action: | Contact your NEC service representative.
|
ISL: IOio# CHch# CHECK
| Cause: | A fault occurred in channel ch# of IO io#.
| io#: | IO number |
| ch#: | Channel number |
For a system control IOX channel, this message is reported by automatic
notification (level 0, type code 21). For a device control IOX channel,
the message is output to the console.
|
| Action: | Contact your NEC service representative.
|
ISL: CPU CHECK CPUNO = 0x cpu#.
| Cause: | A CPU fault occurred.
|
| Action: | Contact your NEC service representative.
|
ISL: Read ISL parameter file name (data = size Byte)
| Cause: | Read from the ISL parameter file is completed. |
| Action: | None. |
ISL: Invalid SVP request. code = %d
| Cause: | An invalid SVP request was made. ISL ignores the request, and continues processing. |
| Action: | None. |
ISL: can not read ISL parameter file. file name
| Cause: | This is an automatic notification message to report that acquisition of the parameter
file from system control IOX failed. The notification level is 0, and type code is 21.
| file name: | ISL parameter file name. |
|
| Action: | Check the system control IOX status, then start ffd (common daemon).
|
ISL: Read IOX time error.
| Cause: | Time acquisition from system control IOX failed. ISL ignores the failure, and continues processing. |
| Action: | None. |
ISL: shish: ISL parameter, max line size over.
| Cause: | More than 160 characters are coded in one line in the ISL parameter file. |
| Action: | Correct the ISL parameter file, then restart the system. |
ISL: mk_islprm: Warning, bootdev not define
| Cause: | Although BOOTDEV is a necessary parameter in the ISL parameter file, it is not found.
ISL waits for ISL command input. |
| Action: | Correct the ISL parameter file, then restart the system. |
ISL: mk_islprm: Warning, rootdev not define
| Cause: | Although ROOTDEV is a necessary parameter in the ISL parameter file, it is not found.
ISL waits for ISL command input. |
| Action: | Correct the ISL parameter file, then restart the system.
|
ISL: mk_islprm: Warning, mvvldev not define
| Cause: | Although MVVLDEV is a necessary parameter in the ISL parameter file, it is not found.
ISL waits for ISL command input. |
| Action: | Correct the ISL parameter file, then restart the system. |
ISL: islprm: ioxtime: ipi3_strategy() error
| Cause: | Time acquisition from system control IOX failed. ISL ignores the failure, and continues processing. |
| Action: | None. |
ISL: invalid IOX time, ID = 0x%x: time = 0x%x 0x%x
| Cause: | Time acquisition from system control IOX failed. ISL ignores the failure, and continues processing.
| ID = 0x%x: | Response identifier |
| time = 0x%x: | Response time |
|
| Action: | None. |
ISL: can not get IOX time, code = 0x%x
| Cause: | Time acquisition from system control IOX failed. ISL ignores the failure, and continues processing.
| code = 0x%x: | Response code |
|
| Action: | None.
|
ISL: islupdate: Illegal partition. num = 0x%x
| Cause: | ISL file update processing failed. The partition number of BOOTDEV coded in the ISL parameter file is
| illegal. num = 0x%x: | Specified partition number |
|
| Action: | Correct the ISL parameter file, then restart the system.
|
ISL: islupdate: Open error.
| Cause: | ISL file update processing failed. Open processing for the disk at the facility address
of BOOTDEV coded in the ISL parameter file failed. |
| Action: | Correct the ISL parameter file or device daemon config file, then restart the system. |
ISL: islupdate: id_vlread() error.
| Cause: | ISL file update processing failed. Read from the disk at the facility address
of BOOTDEV coded in the ISL parameter file failed. |
| Action: | Contact your NEC service representative. |
ISL: islupdate: vl read error.
| Cause: | ISL file update processing failed. Read from the disk at the facility address
of BOOTDEV coded in the ISL parameter file failed. |
| Action: | Contact your NEC service representative. |
ISL: islupdate: %s: INVALID FILE TYPE (0x%04x).
| Cause: | ISL file update processing failed. The specified isl file is not a regular file.
| %s: | Specified ISL file name |
| (0x%x): | File type of the specified isl file |
|
| Action: | Specify a correct isl file name, and reexecute the isl command.
|
ISL: islupdate: %s: FILE SIZE IS TOO LARGE.
| Cause: | ISL file update processing failed. The specified isl file is too large. |
| Action: | Specify a correct isl file name, and reexecute the isl command.
|
ISL: islupdate: XXXXX: I/O error. File offset = 0x%x.
| Cause: | ISL file update processing failed. I/O processing for the isl file failed.
| XXXXXX: | Internal processing number |
|
| Action: | Contact your NEC service representative.
|
ISL: islupdate: XXXXX: Err = 0x%x. File offset = 0x%x.
| Cause: | ISL file update processing failed. I/O processing for the isl file failed.
| XXXXX: | Internal processing number |
| Err = 0x%x: | Error code |
| File offset = 0x%x: | Offset in the isl file |
|
| Action: | Contact your NEC service representative.
|
ISL: islupdate: XXXXX: Short writing. File offset = 0x%x. Length = 0x%x.
Req = 0x%x.
| Cause: | ISL file update processing failed. I/O processing for the isl file failed.
| XXXXX: | Internal processing number |
| File offset = 0x%x: | Offset in the isl file |
| Length = 0x%x: | I/O length |
|
| Action: | Contact your NEC service representative.
|
ISL: SVP disk XXXXX error. off = 0x%x ptr = 0x%x sz = 0x%x
| Cause: | ISL file update processing failed. I/O processing for the isl file failed.
| XXXXX: | Internal processing number |
| off = 0x%x: | Offset in the isl file |
| ptr = 0x%x: | Memory address |
| sz = 0x%x: | I/O length |
|
| Action: | Contact your NEC service representative.
|
ISL: kickdmn: invalid term, bufp = 0x%x.
| Cause: | An invalid termination was reported during IOX daemon start processing. ISL
ignores it, and continues processing. However, later operation may result in an error. |
| Action: | Contact your NEC service representative.
|
ISL: kickdmn: idi3_open() error, ch = 0x%x
| Cause: | The daemon could not be activated.
|
| Action: | Contact your NEC service representative.
|
ISL: kickdmn: ipi3_strategy() error.
| Cause: | The daemon could not be activated. |
| Action: | Contact your NEC service representative.
|
ISL: can not read symbol table (ISL)
| Cause: | ISL read operation failed during ISL update processing. |
| Action: | Check whether the ISL file to be updated is correct.
|
ISL: can not read symbol table (kernel)
| Cause: | The kernel could not be read during kernel load processing.
| Kernel: | Specified kernel name. |
|
| Action: | Check whether the specified kernel is correct.
|
ISL: %s: INVALID FILE TYPE (0x%04x)
| Cause: | The kernel could not be read.
| %s: | Specified kernel name |
| (0x%04x): | File type |
|
| Action: | Check whether the specified kernel is correct.
|
ISL: knlload: invalid partition number. num = 0x%x
| Cause: | The kernel could not be read.
| num = 0x%x: | The partition number of the boot file system is illegal. |
|
| Action: | Correct the partition number of BOOTDEV in the ISL parameter file.
|
ISL: knlload: open error. slv = %d fac = %d inch = %d outch = %d ifld = 0x%x
| Cause: | The kernel could not be read.
| slv = %d: | Slave number of BOOTDEV |
| fac = %d: | Facility number of BOOTDEV |
| inch = %d: | Input channel number of BOOTDEV |
| outch = %d: | Output channel number of BOOTDEV |
| ifld = %d: | I-field of BOOTDEV |
|
| Action: | Check whether the specified kernel is correct.
|
ISL: knlload: id_vlread() error.
| Cause: | The kernel could not be read. |
| Action: | Check whether the boot file system has been created correctly.
|
ISL: knlload: VL read timeout(errno = 0x%x).
| Cause: | The kernel could not be read.
|
| Action: | Check the system control IOX status.
|
ISL: knlload: VL read I/O error(errno = 0x%x).
| Cause: | The kernel could not be read.
|
| Action: | Check the system control IOX status.
|
ISL: knlload: VL read retry over. MAX = 0x%x
| Cause: | The kernel could not be read.
| MAX = 0x%x: | Maximum retry count |
|
| Action: | Check the system control IOX status.
|
ISL: knlload: VL read retry. cnt = 0x%x
| Cause: | The kernel could not be read, and retry processing was performed.
|
| Action: | None.
|
ISL: knlload: FILE SIZE IS TOO LARGE
| Cause: | The kernel could not be read. |
| Action: | The kernel is too large. Check whether the specified kernel is correct.
|
ISL: bread: id_strategy() error
| Cause: | A disk I/O error occurred. |
| Action: | Check the daemon status on IOX.
|
ISL: bread: timeout error(errno = 0x%x).
| Cause: | A disk I/O error occurred.
|
| Action: | Check the daemon status on IOX.
|
ISL: bread: I/O error(errno = 0x%x).
| Cause: | A disk I/O error occurred.
|
| Action: | Check the daemon status on IOX.
|
ISL: bread: I/O error, retry over. MAX = 0x%x
| Cause: | A disk I/O error occurred.
| MAX = 0x%x: | Maximum retry count |
|
| Action: | Check the daemon status on IOX.
|
ISL: bread: I/O retry. cnt = 0x%x
| Cause: | Disk I/O failed, and it was retried.
|
| Action: | Check the daemon status on IOX.
|
ISL: cmd#: ILLEGAL OPTION - opt#
| Cause: | Illegal option opt# is specified in cmd# coded in ISL parameters. |
| Action: | Check the ISL parameters.
|
ISL: cmd#: invalid value = val#.
| Cause: | Option value val# in cmd# coded in ISL parameters is illegal. |
| Action: | Check the ISL parameters.
|
ISL: KERNEL: syntax error.
| Cause: | The kernel name coded in an ISL parameter is illegal. |
| Action: | Specify a correct kernel name.
|
ISL: KERNEL: kernel name size over
| Cause: | The kernel name coded in an ISL parameter is too long. |
| Action: | Specify a kernel name with up to 64 characters.
|
ISL: KERNEL: Invalid kernel name
| Cause: | The kernel name coded in an ISL parameter is illegal. |
| Action: | Code a correct kernel name.
|
ISL: cmd#: already specified.
| Cause: | cmd# is already coded in an ISL parameter. |
| Action: | The second and subsequent ISL parameters are ignored.
|
ISL: cmd#: all options must be specified. (code = 0x%x)
| Cause: | All options are not specified in the cmd# parameter coded in ISL parameters. |
| Action: | The cmd# parameter is ignored.
|
ISL: DUMPDEV: dumpdev is full. (MAX = 32)
| Cause: | Too many dump devices are specified. |
| Action: | Up to 32 dump devices can be specified.
|
ISL: islinfo: invalid format, isl#
| Cause: | isl# coded in the ISLINFO parameter which is an ISL parameter is illegal. |
| Action: | Correct the ISLINFO parameter.
|
ISL: ISL parameter not found, %s.
| Cause: | Illegal parameter %s is coded as an ISL parameter. |
| Action: | Code a correct parameter.
|
ISL: kernel name not found
| Cause: | The specified kernel is not found. |
| Action: | Enter a correct kernel. |
ISL: Invalid kernel name
| Cause: | The specified kernel name is invalid. |
| Action: | Enter a correct kernel name.
|
ISL: kernel name size over
| Cause: | The specified kernel name is too long. |
| Action: | Specify a kernel name with up to 64 characters.
|
ISL: ISL name not found
| Cause: | The specified ISL is not found. |
| Action: | Enter a correct ISL name.
|
ISL: Invalid ISL name
| Cause: | The specified ISL is invalid. |
| Action: | Enter a correct ISL name.
|
ISL: ISL update error
| Cause: | ISL update operation failed. |
| Action: | Contact your NEC service representative.
|
ISL: isl name size over
| Cause: | The specified ISL name is too long. |
| Action: | Specify an ISL name with up to 64 characters.
|
ISL: Re-INIT can not execute
| Cause: | Restart failed. |
| Action: | Contact your NEC service representative.
|
ISL: Can not read ISL parameter file.
| Cause: | The ISL parameters could not be read. |
| Action: | Check the system control IOX status. |
ISL: Warning,isl parameter file pointer is NULL.
| Cause: | No ISL parameters have been read. |
| Action: | Contact your NEC service representative. |
ISL: string size over. max80 bytes
| Cause: | The line of an ISL parameter exceeds 80 characters. |
| Action: | Correct the line so that it contains of up to 80 characters, then perform startup operation again. |
ISL: PROGRAM EXCEPTION. ISW=xxxxxxxx,ICC=xxxxxxxx
| Cause: | An exception occurred during ISL operation.
| ISW: | Cause code of the exception |
| ICC: | Address where the exception occurred |
|
| Action: | Contact your NEC service representative. |
usr_cpsb: xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx
int_cpsb: xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx
| Cause: | In ISL, an exception occurred during dump collection.
The ISL register information is output if the processing cannot
continue. |
| Action: | Contact your NEC service representative. |
ISL: SABORT. message (CALLER=0Xxxxxxxxx)
| Cause: | An internal conflict was detected during ISL operation.
The system aborts. |
| Action: | Contact your NEC service representative. |
ISL: Stop because CPU FAN/TEMP. ALARM
| Cause: | ISL stops because abnormal CPU temperature was detected
during ISL operation. |
| Action: | Contact your NEC service representative. |
ISL: ISL stop because own serial number (%X) wasn't found in nodelist file.
| Cause: | In the cluster system, ISL stops because the hardware serial
number of the local node is not described in the /opt/sx/conf/nodelist
file on SIOX. |
| Action: | Check the /opt/sx/conf/nodelist file on SIOX and reinstall
the file in order to describe the correct serial number. |
ISL: Duplicate nodes are defined in nodelist file. XXXX=xxxx.
| Cause: | The hardware serial number of the node(xxxx) is doubly defined in the cluster system.
|
| Action: | Check the /opt/sx/conf/nodelist file on SIOX and reinstall
the file in order to describe the correct serial number. |
ISL: can not get response from SIOX.
| Cause: | It is not possible to communicate with the SIOX. |
| Action: | Inform to the support center after confirming the state of the channel of the route to the SIOX and the SIOX. |
ISL: Stop because re_init count is overflow.
| Cause: | A failure was detected during ISL operation and an attempt
was made repeatedly to start up the system automatically. However,
the system cannot be activated and ISL stops. |
| Action: | Contact your NEC service representative. |
ISL: IOX reboot occurred, then the system will reboot.
| Cause: | The system is automatically restarted up because an IOX
reboot occurred during ISL operation. |
| Action: | None. |
ISL: CPU CHECK END. CPUNO=xx degraded.
| Cause: | CPU trouble occurred. The recovery process by hardware failed. |
| Action: | Contact your NEC service representative. |
ISL: disk I/O error status = 0x%x type = 0x%x
| Cause: | A failure occurred in the disk device. |
| Action: | Contact your NEC service representative. |
ISL: disk conditional success
| Cause: | A disk device posted the conditional normal termination. |
| Action: | Contact your NEC service representative. |
ISL: disk incomplete
| Cause: | A disk device fails to execute the instruction. |
| Action: | Contact your NEC service representative. |
ISL: disk I/O error command exception
| Cause: | An illegal instruction was issued to a disk device. |
| Action: | Contact your NEC service representative. |
ISL: disk command aborted
| Cause: | A disk device aborted the I/O request. |
| Action: | Contact your NEC service representative. |
ISL: disk I/O error machine exception
| Cause: | A failure occurred in the disk device. |
| Action: | Contact your NEC service representative. |
ISL: disk I/O error intervention required
| Cause: | A disk device issued the intervention request. |
| Action: | Contact your NEC service representative. |
ISL: disk I/O error message/microcode exception
| Cause: | A failure occurred in the disk device. |
| Action: | Contact your NEC service representative. |
ISL: aocspof(2): channel program image %x %x %x %x
| Cause: | A channel program when the system power-off failed. |
| Action: | None. |
IPI-3: invalid slave address xx
| Cause: | The slave address is illegal. |
| Action: | Contact your NEC service representative. |
IPI-3: invalid IO No. (io#)
| Cause: | The IO number is illegal. |
| Action: | Contact your NEC service representative. |
IPI-3: invalid channel No. (ch#)
| Cause: | The channel number is illegal. |
| Action: | Contact your NEC service representative. |
IPI-3: different iors mode (xx) before open
| Cause: | The channel mode is illegal. |
| Action: | Contact your NEC service representative. |
IPI-3: hippi open error xx
| Cause: | Channel opening failed. |
| Action: | Contact your NEC service representative. |
IPI-3: invalid open count
| Cause: | A conflict occurred in the ISL resource. |
| Action: | Contact your NEC service representative. |
IPI-3: different open mode (xx) before open
| Cause: | The channel mode is illegal. |
| Action: | Contact your NEC service representative. |
IPI-3: ipihp open table overflow
| Cause: | A conflict occurred in the ISL resource. |
| Action: | Contact your NEC service representative. |
IPI-3: invalid table number (xx)
| Cause: | A conflict occurred in the ISL resource. |
| Action: | Contact your NEC service representative. |
IPI-3: hippi is not opened
| Cause: | The channel is not open. |
| Action: | Contact your NEC service representative. |
IPI-3: ipihp is not opened (%d)
| Cause: | The channel is not open. |
| Action: | Contact your NEC service representative. |
IPI-3: invalid reference number (xx)
| Cause: | An error occurred in ISL. |
| Action: | Contact your NEC service representative. |
IPI-3: error detected (source)
| Cause: | An error occurred in the channel at the source side. |
| Action: | Contact your NEC service representative. |
IPI-3: I/O error detected (%d)
| Cause: | An I/O error occurred. |
| Action: | Contact your NEC service representative. |
IPI-3: invalid response type detected
| Cause: | An illegal response was received. |
| Action: | Contact your NEC service representative. |
IPI-3: TNR in not read operation
| Cause: | An illegal TNR was received. |
| Action: | Contact your NEC service representative. |
IPI-3: not exist data in TNR
| Cause: | An illegal TNR was received. |
| Action: | Contact your NEC service representative. |
ISL: kick daemon(slave#,facility#) error. reason=msg.
| Cause: | Activating the device indicated by slave# and facility# failed.
|
| Action: | Contact your NEC service representative. |
ISL: device not assigned(slave#,facility#) reason=xx.
| Cause: | Assigning the device indicated by slave# and facility#
failed in the cluster system.
|
| Action: | Contact your NEC service representative. |
ISL: Cluster size of boot file system must be 4096 bytes.
| Cause: | The format of the boot file system is illegal. The format
of the boot file system must be SFS and its cluster size must
be 4096 bytes. |
| Action: | Contact your NEC service representative. |
ISL: INVALID FSMAGIC. NUBMER=xxxxxxxx.
| Cause: | The format of the boot file system is illegal. The format
of the boot file system must be SFS. |
| Action: | Contact your NEC service representative. |
ISL: %s: symbol talbe overflow, symbol number xxxxxx->25000.
| Cause: | The number of symbols of the kernel overflowed. Up to
25000 symbols are processed and the excess symbols are truncated. Then the processing continues. |
| Action: | Contact your NEC service representative. |
ISL: knlload: Disk daemon can not execute.
| Cause: | The disk daemon corresponding to the boot file system cannot be activated. |
| Action: |
Check the reason why the daemon cannot be activated by
referencing the syslog message on SIOX. Contact your NEC service
representative. |
ISL: knlload: invalid address, text address=0x%x.
| Cause: | A kernel cannot be loaded because its text beginning position
is illegal. |
| Action: | Contact your NEC service representative. |
ISL: knlload: invalid address, data address=0x%x.
| Cause: | A kernel cannot be loaded because its data beginning position
is illegal. |
| Action: | Contact your NEC service representative. |
ISL: knlload: invalid address, entry address=0x%x.
| Cause: | A kernel cannot be loaded because its execution beginning
position is illegal. |
| Action: | Contact your NEC service representative. |
ISL: BOOT-FILSYS INVALID FORMAT.
| Cause: | The format of the boot file system is illegal. |
| Action: | Contact your NEC service representative. |
ISL: %s: INVALID MAGIC NUMBER. NUMBER=%04x.
| Cause: | A kernel cannot be loaded because its format is illegal. |
| Action: | Specify a correct kernel name. |
uhip: Data error.
| Cause: | Data is illegal. |
| Action: | Contact your NEC service representative. |
uhip: I/O error.
| Cause: | The channel program abnormally terminated. |
| Action: | Contact your NEC service representative. |
uhip: Address error. IO = xx ch = xx
| Cause: | Data is illegal.
| IO: | Channel number |
| ch: | IO number |
|
| Action: | Contact your NEC service representative. |
uhip: Channel not opened. IO = xx ch = xx
| Cause: | The channel is not opened.
| IO: | IO number |
| ch: | Channel number |
|
| Action: | Contact your NEC service representative. |
uhip: Open mode is invalid. IO = xx ch = xx
| Cause: | The channel cannot be open because the open mode was different.
| IO: | IO number |
| ch: | Channel number |
|
| Action: | Contact your NEC service representative. |
uhip: siopexec() aborted. IO = xx ch = xx code = xx
| Cause: | Issuing the channel program failed.
| IO: | IO number |
| ch: | Channel number |
| code: | Condition code |
|
| Action: | Contact your NEC service representative. |
uhip: cannot get SENSE (retry). IO = xx ch = xx
| Cause: | Reissuing READSTATUS failed.
| IO: | IO number |
| ch: | Channel number |
|
| Action: | Contact your NEC service representative. |
uhip: CP EXECUTION canceled.
| Cause: | The channel program being executed was suspended. |
| Action: | None. |
uhip: Attention: CONNECT DOWN. IO = %d c = %d
| Cause: | The CONNECT signal was changed from 1 to 0 after the connection
was established. |
| Action: | None. |
uhip: Attention: I-field Parity Error. IO = xx c = xx
| Cause: | A parity error of I-field was detected.
The connection establishing request of the corresponding channel is rejected
automatically.
| IO: | IO number |
| ch: | Channel number |
|
| Action: | None. |
uhip: CODE-READ buffer is not assigned. IO = xx c = xx code= xx
| Cause: | The device status is illegal.
| IO: | IO number |
| ch: | Channel number |
| code: | Detection timing |
|
| Action: | Contact your NEC service representative. |
uhip: uhip: siopcancel() aborted. code = xx IO = xx ch = xx
| Cause: | Suspending the channel program being executed failed.
| code: | Condition code |
| IO: | IO number |
| ch: | Channel number |
|
| Action: | Contact your NEC service representative. |
ISL: PCIAxx is not configured.
| Cause: | The specified PCIA is not configured though the ISL tries to initialize it.
|
| Action: | Contact your NEC service representative after confirming the setting of the boot device or dump device. |
ISL: PCIxx Initializing. Please wait max tt sec.
| Cause: | Please wait until the initialization of the PCIA is finished.
| xx: | PCIA number |
| tt: | maximum time |
|
| Action: | None. |
ISL: PCICHxx is not configured.
| Cause: | The specified channel under the PCIA is not configured though the ISL tries to initialize it.
|
| Action: | Contact your NEC service representative after confirming the setting of the boot device or dump device. |
ISL: PCIAAxx disconnected.
| Cause: | The PCIA was disconnected.
|
| Action: | None. |
ISL: scd was already opened.
| Cause: | The specified SCSI disk has already been used. The ISL uses it again.
|
| Action: | None. |
ISL: SCSI disk: xx retry over (c:XX,t:XX,d:XX)
| Cause: | A retry action was unsuccessful.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Contact your NEC service representative. |
ISL: SCSI disk: xx unavailable (c:XX,t:XX,d:XX)
| Cause: | The SCSI disk device has entered an unavailable state.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Contact your NEC service representative. |
ISL: SCSI disk: xx I/O error (c:XX,t:XX,d:XX)
| Cause: | An I/O error was detected.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Contact your NEC service representative. |
ISL: SCSI disk: xx Target is BUSY (c:XX,t:XX,d:XX)
| Cause: | The SCSI disk device is busy.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Check the hardware condition of the
SCSI disk device,
then contact your NEC service representative. |
ISL: SCSI disk: xx Hardware Error (c:XX,t:XX,d:XX)
| Cause: | An unrecoverable hardware failure was detected
.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Contact your NEC service representative. |
ISL: SCSI disk: xx Illegal Request (c:XX,t:XX,d:XX)
| Cause: | An illegal command was detected.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Contact your NEC service representative. |
ISL: SCSI disk: xx Not Ready (c:XX,t:XX,d:XX)
| Cause: | The SCSI disk device is not ready.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Check the hardware condition of the
SCSI disk device,
then contact your NEC service representative. |
ISL: SCSI disk: xx Aborted Command (c:XX,t:XX,d:XX)
| Cause: | The SCSI disk device aborted the command.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Contact your NEC service representative. |
ISL: SCSI disk: xx Unsupported this ANSI_version (c:XX,t:XX,d:XX)
| Cause: | The SCSI disk device is not supported by the SCSI disk driver.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Check the SCSI disk device model. |
ISL: SCSI disk: xx Unsupported this drive type (c:XX,t:XX,d:XX)
| Cause: | The SCSI disk device is not supported by the SCSI disk driver.
| c: | SCSI channel number |
| t: | SCSI ID |
| d: | LUN |
|
| Action: | Check the SCSI disk device model. |
ISL: scpc: PCxxx Execute error, cc=y
| Cause: | An Execute command was unsuccessful in PCxxx equipped
with a SCSI interface card because of cc=y. |
| Action: | Contact your NEC service representative. |
ISL: scpc: PCxxx Unexpected error
| Cause: | An unexpected phenomenon was detected in PCxxx equipped
with a SCSI interface card. |
| Action: | Contact your NEC service representative. |
ISL: scpc: xxx(PCyyy) I/O error, error flags: nnnnnnnn nnnnnnnn
| Cause: | An I/O error was detected in xxx
connected with PCyyy. Error flags indicate the termination status of
Channel Expansion Feature, or the incompatibility detected by the software.
| xxx: | SCSI device name or SCSI-ID/LUN |
|
| Action: | Contact your NEC service representative. |
ISL: scpc: PCxxx Cancel error, cc=y
| Cause: | A Cancel command was unsuccessful in PCxxxequipped
with a SCSI interface card because of cc=y. |
| Action: | Contact your NEC service representative. |
ISL: scpc: PCxxx unavailable
| Cause: | PCxxx equipped with a SCSI interface card has entered
an unavailable state. |
| Action: | Contact your NEC service representative. |
ISL: scpc: xxx(PCyyy) Check Condition
NOTICE: scpc : sense data: zzzzzzzz zzzzzzzz zzzzzzzz zzzz
| Cause: |
A check condition was detected when the inquiry command was executed to
xxx in PCyyy equipped with a SCSI interface card.
| xxx : | SCSI device name or SCSI-ID/LUN |
| zzzzzzzz: | Sense data |
|
| Action: | Contact your NEC service representative. |
ISL: scpc: PCxxx Selterm/Selatt error, cc=y
| Cause: | A Selterm or Selatt command was unsuccessful in PCxxx equipped
with a SCSI interface card because of cc=y. |
| Action: | Contact your NEC service representative. |
ISL: SMT: Device not ready(c:xx t:xx d:xx).
| Cause: | The SCSI tape device was not available. |
| Action: | Make the SCSI device available. |
ISL: SMT: Hardware error(c:xx t:xx d:xx).
| Cause: | An error occurred in the SCSI tape device. |
| Action: | Contact your NEC service representative. |
ISL: SMT: Illeagal device(c:xx t:xx d:xx).
| Cause: | An illegal device was detected. |
| Action: | Contact your NEC service representative. |
ISL: SMT: Retry over(c:xx t:xx d:xx).
| Cause: | Recovery processing for the SCSI tape device failed. |
| Action: | Contact your NEC service representative. |
ISL: SMT: Not supported drive type(c:xx t:xx d:xx).
| Cause: | ISL does not support this device type. |
| Action: | Specify the device type supported by ISL and collect the system dump again. |
ISL: SMT: Device not ready. Change into manual mode and enter (y/n)
| Cause: | The IBM3590 must be in manual mode when collecting the system dump. |
| Action: | When continuing the dump collection on the IBM 3590 device, set the device mode to manual, insert a medium, and enter "y." When "n" is entered, dump collection is aborted. In this case, you can start dump collection from the beginning. |
ISL: SMT: canot allocate memory to use device.
| Cause: | Memory required to use the device could not be reserved. |
| Action: | Specify a device other than SMT and start dump collection from the beginning. |
ISL: SMT: ISL stops by lack of memory.
| Cause: | ISL stopped because the system cannot be activated due to lack of memory. |
| Action: | Use the IOX install tool to set the system so that it does not be activate by the MFF method and re-activate the system. |
ISL: SMT: Enter "y" if the system is rebooted.
| Cause: | Enter "y" when the system can be rebooted. |
| Action: | If necessary, change the IBM3590 mode and enter "y." |
ISL:HIP: Illegal Attention (CH=0xXX)
| Cause: | Attention was reported to unimplemented channel.
| CH=0xXX: | HIPPI channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: Illegal Termination (CH=0xXX)
| Cause: | Termination was reported to unimplemented channel.
| CH=0xXX: | HIPPI channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: Open: Illegal device number (dev=0xXX)
| Cause: | Cannot open channel because illegal device number is specified.
|
| Action: | Specify valid channel. |
ISL:HIP: PC=0xXX, I-Field=0xXXXX: Open: Illegal I-Field(0xXXXX)
| Cause: | Cannot open channel because illegal I-Field is specified.
| PC=0xXX: | Physical channel number |
| I-Field=0xXXXX: | Legal I-Field |
| (0xXXXX): | Illegal I-Field |
|
| Action: | Specify valid channel. |
ISL:HIP: PC=0xXX, LC=0xX: Termination reported
| Cause: | Illegal Termination was reported.
| PC=0xXX: | Physical channel number |
| LC=0xX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX, ULP-id=0xX: Illegal Packet
ISL:HIP: address=0xXXXXXXXXXXXXXX
| Cause: | Cannot continue the operation because illegal packet was received.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| ULP-id=0xX: | ULP-id |
| address=0xXXXXXXXXXXXXXXXX: | Address of packet |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX, ULP-id=0xX: Illegal Packet(ULP-id=0xXX)
| Cause: | Cannot continue the operation because illegal packet was received.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| ULP-id=0xX: | ULP-id |
| (ULP-id=0xX): | Illegal ULP-id |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination
ISL:HIP: status=0xXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX,LC=0xXX: Abnormal Termination: Connection Not Established
ISL:HIP: status=0xXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because connection was not established.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: Hanguped
ISL:HIP: status=0xXXXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXX
| Cause: | Channel program terminated abnormally because the HIPPI connection was hung up.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: INTERCONNECT down
ISL:HIP: status=0xXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because of the deassertion of the
INTERCONNECT signal
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: Illegal Channel Program
ISL:HIP: status=0xXXXXXXXXXXXXXXXX(undefined), CCE=0xXXXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally with undefined status.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: Illegal Address
ISL:HIP: status=0xXXXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because illegal address was specified.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: Illegal Channel Program
ISL:HIP: status=0xXXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because of illegal format of channel program.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: Illegal Channel Type
ISL:HIP: status=0xXXXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because illegal channel type was specified.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: Illegal Length
ISL:HIP: status=0xXXXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because illegal transferred length was specified.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: Illegal SB
ISL:HIP: status=0xXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because of illegal short burst position in
the packet.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: Memory Access Error
ISL:HIP: status=0xXXXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because of memory access error.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Abnormal Termination: REJECT Mode
ISL:HIP: status=0xXXXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because connection mode was REJECT.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Abnormal Termination: Too Big Packet
ISL:HIP: status=0xXXXXXXXXXXXXXXXX, CCE=0xXXXXXXXXXXXXX
| Cause: | Channel program terminated abnormally because of illegal packet size.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| status=0xXXXXXXXXXXXXXXXX: | Termination status |
| CCE=0xXXXXXXXXXXXXXXX: | Last CCE address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Cancel (CC=0xXX)
| Cause: | Cancellation of channel program terminated abnormally.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| CC=0xXX: | Condition code |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Cancel: Not ACTIVE
| Cause: | Cancellation of channel program terminated abnormally because the channel was
not active.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Cancel: Not CONNECT
| Cause: | Cancellation of channel program terminated abnormally because the channel was
not connected.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Cancel: Reply Timeout
| Cause: | Cancellation of channel program timed out.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Channel Status Error (ULP-id=X not found)
| Cause: | Termination of channel program with illegal ULP-id reported.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| ULP-id=X: | ULP-id |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Execerr (CC=0xXX)
| Cause: | Channel program could not be executed.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| CC=0xXX: | Condition code |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Execerr: Illegal Channel Program Address
| Cause: | Channel program could not be executed because illegal address was specified.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Execerr: Not ACTIVE
| Cause: | Channel program could not be executed because the channel was not active.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Execerr: Not CONNECT
| Cause: | Channel program could not be executed because the channel was not connected.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Illegal Buffer status(0xX)
| Cause: | Cannot continue the operation because of illegal status of read buffer.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| (0xX): | Read buffer status |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Illegal Packet (ULP-id=0xXX)
| Cause: | Channel program terminated abnormally because of illegal ULP-id.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| ULP-id=0xXX: | ULP-id |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Illegal Termination (CH=0xXX)
| Cause: | Termination with illegal channel number reported.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| CH=0xXX: | Illegal channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Illegal Termination (Status=0xXX)
| Cause: | Unexpected termination was reported.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| Status=0xXX: | Channel status code |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Illegal Termination Code (Code=0xXX)
| Cause: | Termination with illegal code reported.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| Code=0xXX: | Illegal termination code |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Open: LC Busy
| Cause: | Cannot open channel because the connection establishment failed.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Read Size Error (size=X)
| Cause: | Cannot continue the operation because of illegal packet size.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
| size=X: | Packet size |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX, LC=0xXX: Termination: Not ONLINE
| Cause: | Termination was reported to channel in not ONLINE.
| PC=0xXX: | Physical channel number |
| LC=0xXX: | Logical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Active: Not CONNECT
| Cause: | Changing channel status to active failed because the channel was not connected.
| PC=0xXX: | Physical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Active: INACTIVE
| Cause: | Changing channel condition to active failed because the channel was inactive or
under inactive.
| PC=0xXX: | Physical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Active: Reply Timeout
| Cause: | Changing channel condition to active timed out.
| PC=0xXX: | Physical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Attention (Code=0xXXXXXXXX)
| Cause: | Attention reported with undefined code reported.
| PC=0xXX: | Physical channel number |
| Code=0xXXXXXX: | Undefined attention code |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Attention: CONNECT down
| Cause: | Attention that the deassertion of the CONNECT signal was reported.
| PC=0xXX: | Physical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Attention: I-Field Parity Error
| Cause: | Attention that I-Field parity error was detected was reported.
| PC=0xXX: | Physical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: can't allocate memory
| Cause: | It is not possible to allocate resources.
| PC=0xXX: | Physical channel number |
|
| Action: | None. |
ISL:HIP: PC=0xXX: Channel Status Error (open count XX)
| Cause: | Channel status was illegal.
| PC=0xXX: | Physical channel number |
| open count XX: | Channel open count |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Conenable (CC=0xXX)
| Cause: | Setting channel mode(DISALLOW/ALLOW/REJECT) failed.
| PC=0xXX: | Physical channel number |
| CC=0xXX: | Condition code |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Conenable: INACTIVE
| Cause: | Setting channel mode(DISALLOW/ALLOW/REJECT) failed because the channel
was inactive or under inactive operation.
| PC=0xXX: | Physical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Conenable: Not CONNECT or Source Channel
| Cause: | Setting channel mode(DISALLOW/ALLOW/REJECT) failed because the channel
was not connected or source channel.
| PC=0xXX: | Physical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Conenable: Reply Timeout
| Cause: | Setting channel mode(DISALLOW/ALLOW/REJECT) timed out.
| PC=0xXX: | Physical channel number |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Open: Illegal ULP-id (ULP-id=0xXX)
| Cause: | Cannot open channel because of illegal ULP-id.
| PC=0xXX: | Physical channel number |
| ULP-id=0xXX: | ULP-id |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: Open: Illegal argument(0xXXXX)
| Cause: | Cannot open channel because specified parameter was illegal.
| PC=0xXX: | Physical channel number |
| (0xXXXX): | Parameter |
|
| Action: | Specify valid channel. |
ISL:HIP: PC=0xXX: Open: Illegal function(0xXXXX)
| Cause: | Cannot open channel because specified function address was illegal.
| PC=0xXX: | Physical channel number |
| (0xXXXX): | Function address |
|
| Action: | Specify valid channel. |
ISL:HIP: PC=0xXX: Open: Illegal number(0xXXXX)
| Cause: | Cannot open channel because specified parameter was illegal.
| PC=0xXX: | Physical channel number |
| (0xXXXX): | Parameter |
|
| Action: | Specify valid channel. |
ISL:HIP: PC=0xXX: Open: Not ONLINE
| Cause: | Cannot open channel because the channel was not ONLINE.
| PC=0xXX: | Physical channel number |
|
| Action: | Make the channel ONLINE by devconf(1M-N). |
ISL:HIP: PC=0xXX: Time Out Error
ISL:HIP: address=0xXXXXXXXXXXXXXXX
| Cause: | Timeout operation could not be continued because of no channel program to be timed out.
| PC=0xXX: | Physical channel number |
| address=0xXXXXXXXXXXXXXX: | Channel program address |
|
| Action: | Contact your NEC service representative. |
ISL:HIP: PC=0xXX: ULP-id Error
ISL:HIP: address=0xXXXXXXXXXXXXXXXX, ULP-id=0xX
| Cause: | The operation could not be continued because of packet with illegal ULP-id.
| PC=0xXX: | Physical channel number |
| address=0xXXXXXXXXXXXXXX: | Packet address |
| ULP-id=0xX: | ULP-id |
|
| Action: | Contact your NEC service representative. |
ISL: ies: MACread error. CC=XX status=0xXXXX
| Cause: | Obtaining the MAC address of the
Ethernet device failed. |
| Action: | Contact your NEC service representative. |
ISL: ies: MACread timeout. (PC=XX)
| Cause: | Obtaining the MAC address of the
Ethernet device failed. |
| Action: | Contact your NEC service representative. |
ISL: ies: Selterm/Selatt error. cc=XX
| Cause: | Initializing the Ethernet device failed. |
| Action: | Contact your NEC service representative. |
ISL: ies: can't set address table, (0xXXXX)
| Cause: | Initializing the Ethernet device failed. |
| Action: | Contact your NEC service representative. |
ISL: ies: read error. CC=XX status=0xXXXX
| Cause: | Receiving the Ethernet frame failed. |
| Action: | Contact your NEC service representative. |
ISL: ies: write error. CC=XX status=0xXXXX
| Cause: | Sending the Ethernet frame failed. |
| Action: | Contact your NEC service representative. |
ISL: FCP: PCxxx Cancel error, cc=y
| Cause: | A Cancel command was unsuccessful in PCxxx
equipped
with an FCP interface card because of cc=y. |
| Action: | Contact your NEC service representative. |
ISL: FCP: PCxxx Execute error, cc=y
| Cause: | An Execute command was unsuccessful in PCxxx equipped with an FCP interface card because of cc=y. |
| Action: | Contact your NEC service representative. |
ISL: FCP: xxx(PCyyy) I/O error, error flags: nnnnnnnn nnnnnnnn
| Cause: | An I/O error was detected in xxx
connected with PCyyy. Error flags indicate the termination status of the Channel Expansion Feature, or an incompatibility detected by the software.
xxx : FCP device name or Target-ID/LUN
|
| Action: | Contact your NEC service representative. |
ISL: FCP: PCxxx Selterm/Selatt error, cc=y
| Cause: | A Selterm/Selatt command was unsuccessful in PCxxx equipped
with an FCP interface card because of cc=y. |
| Action: | Contact your NEC service representative. |
ISL: FCP: PCxxx Statcnt(subCMD=0xnn) error, cc=y
| Cause: | A Statcnt(subCMD=0xnn) command was unsuccessful in PCxxx equipped
with an FCP interface card because of cc=y. |
| Action: | Contact your NEC service representative. |
ISL: FCP: PCxxx Unexpected error
| Cause: | An unexpected phenomenon was detected in PCxxx equipped
with an FCP interface card. |
| Action: | Contact your NEC service representative. |
ISL: FCP: PCxxx unavailable
| Cause: | PCxxx equipped with an FCP interface card has entered
the unavailable state. |
| Action: | Contact your NEC service representative. |